Evnroll Mallet Putters

Overview

ER10 Outback Black
Experience the sweetest face in golf with the Evnroll ER10 Outback Black Putter. A lightweight 6062 aluminum body is combined with a rear CNC milled 303 Stainless steel “Outback” shaped weight to elevate stroke consistency and control. Sweet Face Technology utilizes closely spaced, precisely milled grooves to gear the ball back to center for accuracy and consistency on impacts across the face. Two front-to-back sight lines frame the ball at address to help golfers sink more putts.

• Represents a streamlined blend of design and performance technology to inspire greater confidence
• Super stable mallet profile that features a single-bend shaft and face-balanced design for ultra-high MOI
• Designed to eliminate mis-hits by broadening the sweet spot to create the sweetest face in golf
• Sweet Face Technology utilizes closely spaced grooves to create superior roll and softer impact
• Lightweight 6062 aluminum body combined with a rear CNC milled 303 Stainless steel “Outback” shaped weight
• Patented, precise face milling imparts progressively more energy transfer on off-center hits
• Unique milling pattern gears ball back to center for accuracy and consistency across face
• Each specific putter milled to a specific head weight to maintain swing weight for each length
• Two front-to-back sight lines frame the ball at address to help golfers accurately line putts up
• Each head precision milled from 303 SS, then hand ground, finished and assembled
• Black armour finish provides a timeless, player-preferred aesthetic
• Shaft: FST Stepless, .370” tip diameter

ER5 Center Shaft Hatchback
A center-shafted winged mallet design with a “hatched out” center section. Patented.
• CNC Milled in Carlsbad, California USA
• Head Material – 303 stainless steel
• Color – Silver satin finish
• Swing Weight Balanced By Length – 33"@E1, 34”@D9, 35"@E2
• Face Loft – 2 degrees from the shaft
• Lie Angle – 70 degrees
• Stock Grip – Custom EVNROLL non-taper 1.2
• Length – Measured from center of leading edge to butt
• Balance – 10 degrees toe down
• Shaft – FST stepless, .370” tip
• Shafting – straight shaft mounted over a hosel pin

ER5 Hatchback – a classic heel-toe weighted flange blade.
• CNC Milled in Carlsbad, California USA
• Head Material – 303 stainless steel
• Color – Silver satin finish
• Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g
• Face Loft – 2 degrees from the shaft
• Lie Angle – 71 degrees
• Stock Grip – Custom Winn ProX 1.18
• Length – Measured from center of leading edge
• Balance – 5 degrees toe down
• Shaft – FST stepless, .370” tip
• Shafting – Single bend mounted directly into the head

ER5 Hatchback Black – a winged mallet design with a “hatched out” center section.
• CNC Milled in Carlsbad, California USA
• Head Material – 303 stainless steel
• Color – Black armour finish
• Swing Weight Balanced By Length – 33"@E1, 34"@E1, 35"@E4
• Face Loft – 2 degrees from the shaft
• Lie Angle – 70 degrees
• Stock Grip – Custom EVNROLL black pistol grip
• Length – Measured from center of leading edge to butt
• Balance – 25 degrees toe down
• Shaft – FST stepless, .370” tip with black armour finish
• Shafting – Single bend mounted directly into the head

ER6 iRoll-B – an extreme center mass weighted deep mallet.
• CNC Milled in Carlsbad, California USA
• Head Material – Black anodized 6061 aluminum, 303 stainless steel rear-center weight
• Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g
• Face Loft – 2 degrees from the shaft
• Lie Angle – 70 degrees
• Stock Grip – Custom EVNROLL non-taper 1.2
• Length – Measured from center of leading edge to butt
• Balance – 12 degrees toe down
• Shaft – FST stepless, .370” tip
• Shafting – Single bend mounted directly into the head

ER7 FullMallet – a rear perimeter weighted full mallet.
• CNC Milled in Carlsbad, California USA
• Head Material – 303 stainless steel
• Color – Silver satin finish
• Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g
• Face Loft – 2 degrees from the shaft
• Lie Angle – 70 degrees
• Stock Grip – Custom EVNROLL non-taper 1.2
• Length – Measured from center of leading edge to butt
• Balance – 23 degrees toe down
• Shaft – FST stepless, .370” tip
• Shafting – Single bend mounted directly into the head

ER8 TourMallet – a classic mid-sized players mallet.
• CNC Milled in Carlsbad, California USA
• Head Material – 303 stainless steel
• Color – Silver satin finish
• Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g
• Face Loft – 2 degrees from the shaft
• Lie Angle – 70 degrees
• Stock Grip – Custom EVNROLL non-taper 1.2
• Length – Measured from center of leading edge to butt
• Balance – 23 degrees toe down
• Shaft – FST stepless, .370” tip
• Shafting – Single bend mounted directly into the head

ER8.3 Players Mallet – Flow neck players midmallet.
• CNC Milled in Carlsbad, California USA
• Head Material – 303 stainless steel
• Color – Silver satin finish
• Swing Weight Balanced By Length – 33"@E1, 34"@E1, 35"@E4
• Face Loft – 2 degrees from the shaft
• Lie Angle – 70 degrees
• Stock Grip – Custom EVNROLL red pistol grip
• Length – Measured from center of leading edge to butt
• Balance – 60 degrees toe down
• Shaft – FST stepless, .370” tip
• Shafting – Single bend mounted directly into a flow neck heel hosel